81 lines
2.3 KiB
C
81 lines
2.3 KiB
C
|
#pragma once
|
||
|
|
|
||
|
|
#include "wled.h"
|
||
|
|
#include "Arduino.h"
|
||
|
|
|
||
|
|
#include <deque>
|
||
|
|
|
||
|
|
#define USERMOD_ID_BUZZER 900
|
||
|
|
#ifndef USERMOD_BUZZER_PIN
|
||
|
|
#define USERMOD_BUZZER_PIN GPIO_NUM_32
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Usermods allow you to add own functionality to WLED more easily
|
||
|
|
* See: https://github.com/Aircoookie/WLED/wiki/Add-own-functionality
|
||
|
|
*
|
||
|
|
* Using a usermod:
|
||
|
|
* 1. Copy the usermod into the sketch folder (same folder as wled00.ino)
|
||
|
|
* 2. Register the usermod by adding #include "usermod_filename.h" in the top and registerUsermod(new MyUsermodClass()) in the bottom of usermods_list.cpp
|
||
|
|
*/
|
||
|
|
|
||
|
|
class BuzzerUsermod : public Usermod {
|
||
|
|
private:
|
||
|
|
unsigned long lastTime_ = 0;
|
||
|
|
unsigned long delay_ = 0;
|
||
|
|
std::deque<std::pair<uint8_t, unsigned long>> sequence_ {};
|
||
|
|
public:
|
||
|
|
/*
|
||
|
|
* setup() is called once at boot. WiFi is not yet connected at this point.
|
||
|
|
* You can use it to initialize variables, sensors or similar.
|
||
|
|
*/
|
||
|
|
void setup() {
|
||
|
|
// Setup the pin, and default to LOW
|
||
|
|
pinMode(USERMOD_BUZZER_PIN, OUTPUT);
|
||
|
|
digitalWrite(USERMOD_BUZZER_PIN, LOW);
|
||
|
|
|
||
|
|
// Beep on startup
|
||
|
|
sequence_.push_back({ HIGH, 50 });
|
||
|
|
sequence_.push_back({ LOW, 0 });
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
/*
|
||
|
|
* connected() is called every time the WiFi is (re)connected
|
||
|
|
* Use it to initialize network interfaces
|
||
|
|
*/
|
||
|
|
void connected() {
|
||
|
|
// Double beep on WiFi
|
||
|
|
sequence_.push_back({ LOW, 100 });
|
||
|
|
sequence_.push_back({ HIGH, 50 });
|
||
|
|
sequence_.push_back({ LOW, 30 });
|
||
|
|
sequence_.push_back({ HIGH, 50 });
|
||
|
|
sequence_.push_back({ LOW, 0 });
|
||
|
|
}
|
||
|
|
|
||
|
|
/*
|
||
|
|
* loop() is called continuously. Here you can check for events, read sensors, etc.
|
||
|
|
*/
|
||
|
|
void loop() {
|
||
|
|
if (sequence_.size() < 1) return; // Wait until there is a sequence
|
||
|
|
if (millis() - lastTime_ <= delay_) return; // Wait until delay has elapsed
|
||
|
|
|
||
|
|
auto event = sequence_.front();
|
||
|
|
sequence_.pop_front();
|
||
|
|
|
||
|
|
digitalWrite(USERMOD_BUZZER_PIN, event.first);
|
||
|
|
delay_ = event.second;
|
||
|
|
|
||
|
|
lastTime_ = millis();
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
/*
|
||
|
|
* getId() allows you to optionally give your V2 usermod an unique ID (please define it in const.h!).
|
||
|
|
* This could be used in the future for the system to determine whether your usermod is installed.
|
||
|
|
*/
|
||
|
|
uint16_t getId()
|
||
|
|
{
|
||
|
|
return USERMOD_ID_BUZZER;
|
||
|
|
}
|
||
|
|
};
|