WLED/usermods/stairway_wipe_basic/wled06_usermod.ino

/*
 * This file allows you to add own functionality to WLED more easily
 * See: https://github.com/Aircoookie/WLED/wiki/Add-own-functionality
 * EEPROM bytes 2750+ are reserved for your custom use case. (if you extend #define EEPSIZE in wled_eeprom.h)
 * bytes 2400+ are currently ununsed, but might be used for future wled features
 */

//Use userVar0 and userVar1 (API calls &U0=,&U1=, uint16_t)

byte wipeState = 0; //0: inactive 1: wiping 2: solid
unsigned long timeStaticStart = 0;
uint16_t previousUserVar0 = 0;

//comment this out if you want the turn off effect to be just fading out instead of reverse wipe
#define STAIRCASE_WIPE_OFF

//gets called once at boot. Do all initialization that doesn't depend on network here
void userSetup()
{
  //setup PIR sensor here, if needed
}

//gets called every time WiFi is (re-)connected. Initialize own network interfaces here
void userConnected()
{

}

//loop. You can use "if (WLED_CONNECTED)" to check for successful connection
void userLoop()
{
  //userVar0 (U0 in HTTP API):
  //has to be set to 1 if movement is detected on the PIR that is the same side of the staircase as the ESP8266
  //has to be set to 2 if movement is detected on the PIR that is the opposite side
  //can be set to 0 if no movement is detected. Otherwise LEDs will turn off after a configurable timeout (userVar1 seconds)

  if (userVar0 > 0)
  {
    if ((previousUserVar0 == 1 && userVar0 == 2) || (previousUserVar0 == 2 && userVar0 == 1)) wipeState = 3; //turn off if other PIR triggered
    previousUserVar0 = userVar0;
    
    if (wipeState == 0) {
      startWipe();
      wipeState = 1;
    } else if (wipeState == 1) { //wiping
      uint32_t cycleTime = 360 + (255 - effectSpeed)*75; //this is how long one wipe takes (minus 25 ms to make sure we switch in time)
      if (millis() + strip.timebase > (cycleTime - 25)) { //wipe complete
        effectCurrent = FX_MODE_STATIC;
        timeStaticStart = millis();
        colorUpdated(CALL_MODE_NOTIFICATION);
        wipeState = 2;
      }
    } else if (wipeState == 2) { //static
      if (userVar1 > 0) //if U1 is not set, the light will stay on until second PIR or external command is triggered
      {
        if (millis() - timeStaticStart > userVar1*1000) wipeState = 3;
      }
    } else if (wipeState == 3) { //switch to wipe off
      #ifdef STAIRCASE_WIPE_OFF
      effectCurrent = FX_MODE_COLOR_WIPE;
      strip.timebase = 360 + (255 - effectSpeed)*75 - millis(); //make sure wipe starts fully lit
      colorUpdated(CALL_MODE_NOTIFICATION);
      wipeState = 4;
      #else
      turnOff();
      #endif
    } else { //wiping off
      if (millis() + strip.timebase > (725 + (255 - effectSpeed)*150)) turnOff(); //wipe complete
    }
  } else {
    wipeState = 0; //reset for next time
    if (previousUserVar0) {
      #ifdef STAIRCASE_WIPE_OFF
      userVar0 = previousUserVar0;
      wipeState = 3;
      #else
      turnOff();
      #endif
    }
    previousUserVar0 = 0;
  }
}

void startWipe()
{
  bri = briLast; //turn on
  transitionDelayTemp = 0; //no transition
  effectCurrent = FX_MODE_COLOR_WIPE;
  resetTimebase(); //make sure wipe starts from beginning

  //set wipe direction
  WS2812FX::Segment& seg = strip.getSegment(0);
  bool doReverse = (userVar0 == 2);
  seg.setOption(1, doReverse);

  colorUpdated(CALL_MODE_NOTIFICATION);
}

void turnOff()
{
  #ifdef STAIRCASE_WIPE_OFF
  transitionDelayTemp = 0; //turn off immediately after wipe completed
  #else
  transitionDelayTemp = 4000; //fade out slowly
  #endif
  bri = 0;
  colorUpdated(CALL_MODE_NOTIFICATION);
  wipeState = 0;
  userVar0 = 0;
  previousUserVar0 = 0;
}