56 lines
2.9 KiB
Markdown
56 lines
2.9 KiB
Markdown
|
# :battery: Battery status/level Usermod :battery:
|
||
|
|
|
||
|
|
This Usermod allows you to monitor the battery level of your battery powered project.
|
||
|
|
|
||
|
|
You can see the battery level in the `info modal` right under the `estimated current`.
|
||
|
|
|
||
|
|
For this to work the positive side of the (18650) battery must be connected to pin `A0` of the d1mini/esp8266 with a 100k ohm resistor (see [Useful Links](#useful-links)).
|
||
|
|
|
||
|
|
If you have a esp32 board it is best to connect the positive side of the battery to ADC1 (GPIO32 - GPIO39)
|
||
|
|
|
||
|
|
## Installation
|
||
|
|
|
||
|
|
define `USERMOD_BATTERY_STATUS_BASIC` in `my_config.h`
|
||
|
|
|
||
|
|
### Define Your Options
|
||
|
|
|
||
|
|
* `USERMOD_BATTERY_STATUS_BASIC` - define this (in `my_config.h`) to have this user mod included wled00\usermods_list.cpp
|
||
|
|
* `USERMOD_BATTERY_MEASUREMENT_PIN` - defaults to A0 on esp8266 and GPIO32 on esp32
|
||
|
|
* `USERMOD_BATTERY_MEASUREMENT_INTERVAL` - the frequency to check the battery, defaults to 30 seconds
|
||
|
|
* `USERMOD_BATTERY_MIN_VOLTAGE` - minimum voltage of the Battery used, default is 2.6 (18650 battery standard)
|
||
|
|
* `USERMOD_BATTERY_MAX_VOLTAGE` - maximum voltage of the Battery used, default is 4.2 (18650 battery standard)
|
||
|
|
|
||
|
|
All parameters can be configured at runtime using Usermods settings page.
|
||
|
|
|
||
|
|
## Important :warning:
|
||
|
|
* Make sure you know your battery specification ! not every battery is the same !
|
||
|
|
* Example:
|
||
|
|
|
||
|
|
| Your battery specification table | | Options you can define |
|
||
|
|
| :-------------------------------- |:--------------- | :---------------------------- |
|
||
|
|
| Capacity | 3500mAh 12,5 Wh | |
|
||
|
|
| Minimum capacity | 3350mAh 11,9 Wh | |
|
||
|
|
| Rated voltage | 3.6V - 3.7V | |
|
||
|
|
| **Charging end voltage** | **4,2V ± 0,05** | `USERMOD_BATTERY_MAX_VOLTAGE` |
|
||
|
|
| **Discharge voltage** | **2,5V** | `USERMOD_BATTERY_MIN_VOLTAGE` |
|
||
|
|
| Max. discharge current (constant) | 10A (10000mA) | |
|
||
|
|
| max. charging current | 1.7A (1700mA) | |
|
||
|
|
| ... | ... | ... |
|
||
|
|
| .. | .. | .. |
|
||
|
|
|
||
|
|
Specification from: [Molicel INR18650-M35A, 3500mAh 10A Lithium-ion battery, 3.6V - 3.7V](https://www.akkuteile.de/lithium-ionen-akkus/18650/molicel/molicel-inr18650-m35a-3500mah-10a-lithium-ionen-akku-3-6v-3-7v_100833)
|
||
|
|
|
||
|
|
## Useful Links
|
||
|
|
* https://lazyzero.de/elektronik/esp8266/wemos_d1_mini_a0/start
|
||
|
|
* https://arduinodiy.wordpress.com/2016/12/25/monitoring-lipo-battery-voltage-with-wemos-d1-minibattery-shield-and-thingspeak/
|
||
|
|
|
||
|
|
## Change Log
|
||
|
|
|
||
|
|
2021-08-15
|
||
|
|
* changed `USERMOD_BATTERY_MIN_VOLTAGE` to 2.6 volt as default for 18650 batteries
|
||
|
|
* Updated readme, added specification table
|
||
|
|
|
||
|
|
2021-08-10
|
||
|
|
* Created
|
||
|
|
|