WLED/usermods/Temperature/usermod_temperature.h

174 lines
5.8 KiB
C
Raw Normal View History

2020-05-28 02:20:02 +02:00
#pragma once
#include "wled.h"
#include <DallasTemperature.h> //DS18B20
//Pin defaults for QuinLed Dig-Uno
#ifndef TEMPERATURE_PIN
2020-05-28 02:20:02 +02:00
#ifdef ARDUINO_ARCH_ESP32
#define TEMPERATURE_PIN 18
#else //ESP8266 boards
#define TEMPERATURE_PIN 14
#endif
#endif
2020-05-28 02:20:02 +02:00
// the frequency to check temperature, 1 minute
#ifndef USERMOD_DALLASTEMPERATURE_MEASUREMENT_INTERVAL
#define USERMOD_DALLASTEMPERATURE_MEASUREMENT_INTERVAL 60000
#endif
2020-05-28 02:20:02 +02:00
// how many seconds after boot to take first measurement, 20 seconds
#ifndef USERMOD_DALLASTEMPERATURE_FIRST_MEASUREMENT_AT
#define USERMOD_DALLASTEMPERATURE_FIRST_MEASUREMENT_AT 20000
#endif
2020-05-28 02:20:02 +02:00
OneWire oneWire(TEMPERATURE_PIN);
DallasTemperature sensor(&oneWire);
class UsermodTemperature : public Usermod {
private:
// The device's unique 64-bit serial code stored in on-board ROM.
// Reading directly from the sensor device address is faster than
// reading from index. When reading by index, DallasTemperature
// must first look up the device address at the specified index.
DeviceAddress sensorDeviceAddress;
// set last reading as "40 sec before boot", so first reading is taken after 20 sec
unsigned long lastMeasurement = UINT32_MAX - (USERMOD_DALLASTEMPERATURE_MEASUREMENT_INTERVAL - USERMOD_DALLASTEMPERATURE_FIRST_MEASUREMENT_AT);
// last time requestTemperatures was called
// used to determine when we can read the sensors temperature
// we have to wait at least 93.75 ms after requestTemperatures() is called
unsigned long lastTemperaturesRequest;
float temperature = -100; // default to -100, DS18B20 only goes down to -50C
// indicates requestTemperatures has been called but the sensor measurement is not complete
bool waitingForConversion = false;
// flag to indicate we have finished the first getTemperature call
// allows this library to report to the user how long until the first
// measurement
bool getTemperatureComplete = false;
// flag set at startup if DS18B20 sensor not found, avoids trying to keep getting
// temperature if flashed to a board without a sensor attached
bool disabled = false;
void requestTemperatures() {
// there is requestTemperaturesByAddress however it
// appears to do more work,
// TODO: measure exection time difference
sensor.requestTemperatures();
lastTemperaturesRequest = millis();
waitingForConversion = true;
}
void getTemperature() {
if (strip.isUpdating()) return;
#ifdef USERMOD_DALLASTEMPERATURE_CELSIUS
temperature = sensor.getTempC(sensorDeviceAddress);
2020-05-28 02:20:02 +02:00
#else
temperature = sensor.getTempF(sensorDeviceAddress);
2020-05-28 02:20:02 +02:00
#endif
lastMeasurement = millis();
waitingForConversion = false;
getTemperatureComplete = true;
2020-05-28 02:20:02 +02:00
}
public:
2020-05-28 02:20:02 +02:00
void setup() {
sensor.begin();
// get the unique 64-bit serial code stored in on-board ROM
// if getAddress returns false, the sensor was not found
disabled = !sensor.getAddress(sensorDeviceAddress, 0);
if (!disabled) {
DEBUG_PRINTLN(F("Dallas Temperature found"));
// set the resolution for this specific device
sensor.setResolution(sensorDeviceAddress, 9, true);
// do not block waiting for reading
sensor.setWaitForConversion(false);
// allocate pin & prevent other use
if (!pinManager.allocatePin(TEMPERATURE_PIN,false))
disabled = true;
} else {
DEBUG_PRINTLN(F("Dallas Temperature not found"));
}
2020-05-28 02:20:02 +02:00
}
void loop() {
if (disabled || strip.isUpdating()) return;
unsigned long now = millis();
// check to see if we are due for taking a measurement
// lastMeasurement will not be updated until the conversion
// is complete the the reading is finished
if (now - lastMeasurement < USERMOD_DALLASTEMPERATURE_MEASUREMENT_INTERVAL) return;
// we are due for a measurement, if we are not already waiting
// for a conversion to complete, then make a new request for temps
if (!waitingForConversion)
2020-05-28 02:20:02 +02:00
{
requestTemperatures();
return;
}
2020-05-28 02:20:02 +02:00
// we were waiting for a conversion to complete, have we waited log enough?
if (now - lastTemperaturesRequest >= 94 /* 93.75ms per the datasheet */)
{
getTemperature();
2020-05-28 02:20:02 +02:00
if (WLED_MQTT_CONNECTED) {
char subuf[45];
2020-05-28 02:20:02 +02:00
strcpy(subuf, mqttDeviceTopic);
if (-100 <= temperature) {
// dont publish super low temperature as the graph will get messed up
// the DallasTemperature library returns -127C or -196.6F when problem
// reading the sensor
strcat_P(subuf, PSTR("/temperature"));
mqtt->publish(subuf, 0, true, String(temperature).c_str());
} else {
// publish something else to indicate status?
}
2020-05-28 02:20:02 +02:00
}
}
}
void addToJsonInfo(JsonObject& root) {
// dont add temperature to info if we are disabled
if (disabled) return;
JsonObject user = root[F("u")];
if (user.isNull()) user = root.createNestedObject(F("u"));
2020-05-28 02:20:02 +02:00
JsonArray temp = user.createNestedArray(F("Temperature"));
if (!getTemperatureComplete) {
// if we haven't read the sensor yet, let the user know
// that we are still waiting for the first measurement
temp.add((USERMOD_DALLASTEMPERATURE_FIRST_MEASUREMENT_AT - millis()) / 1000);
temp.add(F(" sec until read"));
return;
}
if (temperature <= -100) {
2020-05-28 02:20:02 +02:00
temp.add(0);
temp.add(F(" Sensor Error!"));
2020-05-28 02:20:02 +02:00
return;
}
temp.add(temperature);
#ifdef USERMOD_DALLASTEMPERATURE_CELSIUS
temp.add(F("°C"));
2020-05-28 02:20:02 +02:00
#else
temp.add(F("°F"));
2020-05-28 02:20:02 +02:00
#endif
}
uint16_t getId()
{
return USERMOD_ID_TEMPERATURE;
}
};