Trying to fix failed build (#756)

platformio.ini

@@ -28,6 +28,7 @@ default_envs = d1_mini, esp01, esp01_1m_ota, esp32dev
 ; default_envs = esp01_1m_full
 ; default_envs = esp07
 ; default_envs = d1_mini
+; default_envs = heltec_wifi_kit_8
 ; default_envs = d1_mini_debug
 ; default_envs = esp32dev
 ; default_envs = esp8285_4CH_MagicHome
@@ -151,8 +152,8 @@ lib_deps =
   #For use SSD1306 OLED display uncomment following
     #U8g2@~2.27.2
   #For Dallas sensor uncomment following 2 lines
-    #DallasTemperature@~3.8.0
-    #OneWire@~2.3.5
+    DallasTemperature@~3.8.0
+    OneWire@~2.3.5
 lib_ignore =
     AsyncTCP
 
@@ -197,6 +198,12 @@ platform = ${common.platform_latest}
 board_build.ldscript = ${common.ldscript_4m1m}
 build_flags = ${common.build_flags_esp8266} 
 
+[env:heltec_wifi_kit_8]
+board = d1_mini
+platform = ${common.platform_latest}
+board_build.ldscript = ${common.ldscript_4m1m}
+build_flags = ${common.build_flags_esp8266}
+
 [env:esp32dev]
 board = esp32dev
 platform = espressif32@1.11.2

usermods/QuinLED_Dig_Uno_Temp_MQTT/readme.txt

@@ -1,8 +1,7 @@
-These files allow WLED 0.8.6 to report the temp sensor on the Quinled board to MQTT. I use it to report the board temp to Home Assistant via MQTT, so it will send notifications if something happens and the board start to heat up.
+These files allow WLED 0.9.1 to report the temp sensor on the Quinled board to MQTT. I use it to report the board temp to Home Assistant via MQTT, so it will send notifications if something happens and the board start to heat up.
 
 This code uses Aircookie's WLED software. It has a premade file for user modifications. I use it to publish the temperature from the dallas temperature sensor on the Quinled board. The entries for the top of the WLED00 file, initializes the required libraries, and variables for the sensor. The .ino file waits for 60 seconds, and checks to see if the MQTT server is connected (thanks Aircoookie). It then poles the sensor, and published it using the MQTT service already running, using the main topic programmed in the WLED UI.
 
 To install:
 
-Add the entries in the WLED00 file to the top of the same file from Aircoookies WLED.
 Replace the WLED06_usermod.ino file in Aircoookies WLED folder.

usermods/QuinLED_Dig_Uno_Temp_MQTT/wled00.txt

@@ -1,8 +0,0 @@
-//Intiating code for QuinLED Dig-Uno temp sensor
-//Uncomment Celsius if that is your prefered temperature scale
-#include <DallasTemperature.h>
-OneWire oneWire(14); 
-DallasTemperature sensors(&oneWire);
-long temptimer = millis();
-long lastMeasure = 0;
-//#define Celsius

usermods/QuinLED_Dig_Uno_Temp_MQTT/wled06_usermod.ino

@@ -1,8 +1,19 @@
-//starts Dallas Temp service on boot
+//Intiating code for QuinLED Dig-Uno temp sensor
+//Uncomment Celsius if that is your prefered temperature scale
+#include <DallasTemperature.h> //Dallastemperature sensor
+#ifdef ARDUINO_ARCH_ESP32 //ESP32 boards
+OneWire oneWire(18);
+#else //ESP8266 boards
+OneWire oneWire(14);
+#endif
+DallasTemperature sensor(&oneWire);
+long temptimer = millis();
+long lastMeasure = 0;
+#define Celsius // Show temperature mesaurement in Celcius otherwise is in Fahrenheit
 void userSetup()
 {
 // Start the DS18B20 sensor
-  sensors.begin(); 
+  sensor.begin();
 }
     
 //gets called every time WiFi is (re-)connected. Initialize own network interfaces here
@@ -21,11 +32,11 @@ void userLoop()
     
 //Check if MQTT Connected, otherwise it will crash the 8266
     if (mqtt != nullptr){
-      sensors.requestTemperatures();
+      sensor.requestTemperatures();
 
 //Gets prefered temperature scale based on selection in definitions section
       #ifdef Celsius
-      float board_temperature = sensors.getTempCByIndex(0);
+      float board_temperature = sensor.getTempCByIndex(0);
       #else
       float board_temperature = sensors.getTempFByIndex(0);
       #endif

usermods/Wemos_D1_mini+Wemos32_mini_shield/wled06_usermod.ino

@@ -31,9 +31,8 @@ U8X8_SSD1306_128X32_UNIVISION_HW_I2C u8x8(U8X8_PIN_NONE, U8X8_PIN_SCL, U8X8_PIN_
 // --> Second choise of cheap I2C OLED 128X64 0.96" or 1.3"
 //U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(U8X8_PIN_NONE, U8X8_PIN_SCL, U8X8_PIN_SDA); // Pins are Reset, SCL, SDA
 // --> Third choise of Heltec WiFi-Kit-8 OLED 128X32 0.91"
-//U8X8_SSD1306_128X32_UNIVISION_HW_I2C u8x8(U8X8_PIN_RESET, U8X8_PIN_SCL, U8X8_PIN_SDA); // Constracor for Heltec WiFi-Kit-8
-// gets called once at boot. Do all initialization that doesn't depend on
-// network here
+//U8X8_SSD1306_128X32_UNIVISION_HW_I2C u8x8(U8X8_PIN_RESET, U8X8_PIN_SCL, U8X8_PIN_SDA); // Constructor for Heltec WiFi-Kit-8
+// gets called once at boot. Do all initialization that doesn't depend on network here
 void userSetup() {
   sensor.begin(); //Start Dallas temperature sensor
   u8x8.begin();