<p align="center">
  <img width="700" src="assets/battery_usermod_logo.png">
</p>

# Welcome to the battery usermod! 🔋

Enables battery level monitoring of your project.

For this to work, the positive side of the (18650) battery must be connected to pin `A0` of the d1 mini/esp8266 with a 100k Ohm resistor (see [Useful Links](#useful-links)).

If you have an ESP32 board, connect the positive side of the battery to ADC1 (GPIO32 - GPIO39)

<p align="center">
  <img width="500" src="assets/battery_info_screen.png">
</p>

## ⚙️ Features

- 💯 Displays current battery voltage 
- 🚥 Displays battery level
- 🚫 Auto-off with configurable Threshold
- 🚨 Low power indicator with many configuration posibilities

## 🎈 Installation

define `USERMOD_BATTERY` in `wled00/my_config.h`

### Example wiring

<p align="center">
  <img width="300" src="assets/battery_connection_schematic_01.png">
</p>

### Define Your Options

| Name                                            | Unit        | Description                                                                           |
| ----------------------------------------------- | ----------- |-------------------------------------------------------------------------------------- |
| `USERMOD_BATTERY`                               |             | define this (in `my_config.h`) to have this usermod included wled00\usermods_list.cpp |
| `USERMOD_BATTERY_USE_LIPO`                      |             | define this (in `my_config.h`) if you use LiPo rechargeables (1S)                     |
| `USERMOD_BATTERY_MEASUREMENT_PIN`               |             | defaults to A0 on ESP8266 and GPIO35 on ESP32                                         |
| `USERMOD_BATTERY_MEASUREMENT_INTERVAL`          | ms          | battery check interval. defaults to 30 seconds                                        |
| `USERMOD_BATTERY_MIN_VOLTAGE`                   | v           | minimum battery voltage. default is 2.6 (18650 battery standard)                      |
| `USERMOD_BATTERY_MAX_VOLTAGE`                   | v           | maximum battery voltage. default is 4.2 (18650 battery standard)                      |
| `USERMOD_BATTERY_TOTAL_CAPACITY`                | mAh         | the capacity of all cells in parralel sumed up                                        |
| `USERMOD_BATTERY_CALIBRATION`                   |             | offset / calibration number, fine tune the measured voltage by the microcontroller    |
| Auto-Off                                        | ---         | ---                                                                                   |
| `USERMOD_BATTERY_AUTO_OFF_ENABLED`              | true/false  | enables auto-off                                                                      |
| `USERMOD_BATTERY_AUTO_OFF_THRESHOLD`            | % (0-100)   | when this threshold is reached master power turns off                                 |
| Low-Power-Indicator                             | ---         | ---                                                                                   |
| `USERMOD_BATTERY_LOW_POWER_INDICATOR_ENABLED`   | true/false  | enables low power indication                                                          |
| `USERMOD_BATTERY_LOW_POWER_INDICATOR_PRESET`    | preset id   | when low power is detected then use this preset to indicate low power                 |
| `USERMOD_BATTERY_LOW_POWER_INDICATOR_THRESHOLD` | % (0-100)   | when this threshold is reached low power gets indicated                               |
| `USERMOD_BATTERY_LOW_POWER_INDICATOR_DURATION`  | seconds     | for this long the configured preset is played                                         |

All parameters can be configured at runtime via the Usermods settings page.

## ⚠️ Important

- Make sure you know your battery specifications! All batteries are **NOT** the same!
- Example:

| Your battery specification table  |                 | Options you can define        | 
| :-------------------------------- |:--------------- | :---------------------------- |
| Capacity                          | 3500mAh 12,5 Wh |                               |
| Minimum capacity                  | 3350mAh 11,9 Wh |                               |
| Rated voltage                     | 3.6V - 3.7V     |                               |
| **Charging end voltage**          | **4,2V ± 0,05** | `USERMOD_BATTERY_MAX_VOLTAGE` |
| **Discharge voltage**             | **2,5V**        | `USERMOD_BATTERY_MIN_VOLTAGE` |
| Max. discharge current (constant) | 10A (10000mA)   |                               |
| max. charging current             | 1.7A (1700mA)   |                               |
| ...                               | ...             | ...                           |
| ..                                | ..              | ..                            |

Specification from:  [Molicel INR18650-M35A, 3500mAh 10A Lithium-ion battery, 3.6V - 3.7V](https://www.akkuteile.de/lithium-ionen-akkus/18650/molicel/molicel-inr18650-m35a-3500mah-10a-lithium-ionen-akku-3-6v-3-7v_100833)

## 🌐 Useful Links

- https://lazyzero.de/elektronik/esp8266/wemos_d1_mini_a0/start
- https://arduinodiy.wordpress.com/2016/12/25/monitoring-lipo-battery-voltage-with-wemos-d1-minibattery-shield-and-thingspeak/

## 📝 Change Log

2023-01-04

- basic support for LiPo rechargeable batteries ( `-D USERMOD_BATTERY_USE_LIPO`)
- improved support for esp32 (read calibrated voltage)
- corrected config saving (measurement pin, and battery min/max were lost)
- various bugfixes

2022-12-25

- added "auto-off" feature
- added "low-power-indication" feature
- added "calibration/offset" field to configuration page
- added getter and setter, so that user usermods could interact with this one
- update readme (added new options, made it markdownlint compliant)

2021-09-02

- added "Battery voltage" to info
- added circuit diagram to readme
- added MQTT support, sending battery voltage
- minor fixes

2021-08-15

- changed `USERMOD_BATTERY_MIN_VOLTAGE` to 2.6 volt as default for 18650 batteries
- Updated readme, added specification table

2021-08-10

- Created