#ifndef WLED_CONST_H #define WLED_CONST_H /* * Readability defines and their associated numerical values + compile-time constants */ //Defaults #define DEFAULT_CLIENT_SSID "Your_Network" #define DEFAULT_AP_PASS "wled1234" #define DEFAULT_OTA_PASS "wledota" //increase if you need more #ifndef WLED_MAX_USERMODS #ifdef ESP8266 #define WLED_MAX_USERMODS 4 #else #define WLED_MAX_USERMODS 6 #endif #endif #ifndef WLED_MAX_BUSSES #ifdef ESP8266 #define WLED_MAX_BUSSES 3 #else #ifdef CONFIG_IDF_TARGET_ESP32S2 #define WLED_MAX_BUSSES 5 #else #define WLED_MAX_BUSSES 10 #endif #endif #endif #ifndef WLED_MAX_BUTTONS #ifdef ESP8266 #define WLED_MAX_BUTTONS 2 #else #define WLED_MAX_BUTTONS 4 #endif #endif #ifdef ESP8266 #define WLED_MAX_COLOR_ORDER_MAPPINGS 5 #else #define WLED_MAX_COLOR_ORDER_MAPPINGS 10 #endif //Usermod IDs #define USERMOD_ID_RESERVED 0 //Unused. Might indicate no usermod present #define USERMOD_ID_UNSPECIFIED 1 //Default value for a general user mod that does not specify a custom ID #define USERMOD_ID_EXAMPLE 2 //Usermod "usermod_v2_example.h" #define USERMOD_ID_TEMPERATURE 3 //Usermod "usermod_temperature.h" #define USERMOD_ID_FIXNETSERVICES 4 //Usermod "usermod_Fix_unreachable_netservices.h" #define USERMOD_ID_PIRSWITCH 5 //Usermod "usermod_PIR_sensor_switch.h" #define USERMOD_ID_IMU 6 //Usermod "usermod_mpu6050_imu.h" #define USERMOD_ID_FOUR_LINE_DISP 7 //Usermod "usermod_v2_four_line_display.h #define USERMOD_ID_ROTARY_ENC_UI 8 //Usermod "usermod_v2_rotary_encoder_ui.h" #define USERMOD_ID_AUTO_SAVE 9 //Usermod "usermod_v2_auto_save.h" #define USERMOD_ID_DHT 10 //Usermod "usermod_dht.h" #define USERMOD_ID_MODE_SORT 11 //Usermod "usermod_v2_mode_sort.h" #define USERMOD_ID_VL53L0X 12 //Usermod "usermod_vl53l0x_gestures.h" #define USERMOD_ID_MULTI_RELAY 13 //Usermod "usermod_multi_relay.h" #define USERMOD_ID_ANIMATED_STAIRCASE 14 //Usermod "Animated_Staircase.h" #define USERMOD_ID_RTC 15 //Usermod "usermod_rtc.h" #define USERMOD_ID_ELEKSTUBE_IPS 16 //Usermod "usermod_elekstube_ips.h" #define USERMOD_ID_SN_PHOTORESISTOR 17 //Usermod "usermod_sn_photoresistor.h" #define USERMOD_ID_BATTERY_STATUS_BASIC 18 //Usermod "usermod_v2_battery_status_basic.h" #define USERMOD_ID_PWM_FAN 19 //Usermod "usermod_PWM_fan.h" #define USERMOD_ID_BH1750 20 //Usermod "usermod_bh1750.h" #define USERMOD_ID_SEVEN_SEGMENT_DISPLAY 21 //Usermod "usermod_v2_seven_segment_display.h" #define USERMOD_RGB_ROTARY_ENCODER 22 //Usermod "rgb-rotary-encoder.h" #define USERMOD_ID_QUINLED_AN_PENTA 23 //Usermod "quinled-an-penta.h" #define USERMOD_ID_SSDR 24 //Usermod "usermod_v2_seven_segment_display_reloaded.h" #define USERMOD_ID_CRONIXIE 25 //Usermod "usermod_cronixie.h" #define USERMOD_ID_WIZLIGHTS 26 //Usermod "wizlights.h" #define USERMOD_ID_WORDCLOCK 27 //Usermod "usermod_v2_word_clock.h" #define USERMOD_ID_MY9291 28 //Usermod "usermod_MY9291.h" #define USERMOD_ID_SI7021_MQTT_HA 29 //Usermod "usermod_si7021_mqtt_ha.h" #define USERMOD_ID_BME280 30 //Usermod "usermod_bme280.h //Access point behavior #define AP_BEHAVIOR_BOOT_NO_CONN 0 //Open AP when no connection after boot #define AP_BEHAVIOR_NO_CONN 1 //Open when no connection (either after boot or if connection is lost) #define AP_BEHAVIOR_ALWAYS 2 //Always open #define AP_BEHAVIOR_BUTTON_ONLY 3 //Only when button pressed for 6 sec //Notifier callMode #define CALL_MODE_INIT 0 //no updates on init, can be used to disable updates #define CALL_MODE_DIRECT_CHANGE 1 #define CALL_MODE_BUTTON 2 //default button actions applied to selected segments #define CALL_MODE_NOTIFICATION 3 #define CALL_MODE_NIGHTLIGHT 4 #define CALL_MODE_NO_NOTIFY 5 #define CALL_MODE_FX_CHANGED 6 //no longer used #define CALL_MODE_HUE 7 #define CALL_MODE_PRESET_CYCLE 8 #define CALL_MODE_BLYNK 9 #define CALL_MODE_ALEXA 10 #define CALL_MODE_WS_SEND 11 //special call mode, not for notifier, updates websocket only #define CALL_MODE_BUTTON_PRESET 12 //button/IR JSON preset/macro //RGB to RGBW conversion mode #define RGBW_MODE_MANUAL_ONLY 0 //No automatic white channel calculation. Manual white channel slider #define RGBW_MODE_AUTO_BRIGHTER 1 //New algorithm. Adds as much white as the darkest RGBW channel #define RGBW_MODE_AUTO_ACCURATE 2 //New algorithm. Adds as much white as the darkest RGBW channel and subtracts this amount from each RGB channel #define RGBW_MODE_DUAL 3 //Manual slider + auto calculation. Automatically calculates only if manual slider is set to off (0) #define RGBW_MODE_LEGACY 4 //Old floating algorithm. Too slow for realtime and palette support //realtime modes #define REALTIME_MODE_INACTIVE 0 #define REALTIME_MODE_GENERIC 1 #define REALTIME_MODE_UDP 2 #define REALTIME_MODE_HYPERION 3 #define REALTIME_MODE_E131 4 #define REALTIME_MODE_ADALIGHT 5 #define REALTIME_MODE_ARTNET 6 #define REALTIME_MODE_TPM2NET 7 #define REALTIME_MODE_DDP 8 //realtime override modes #define REALTIME_OVERRIDE_NONE 0 #define REALTIME_OVERRIDE_ONCE 1 #define REALTIME_OVERRIDE_ALWAYS 2 //E1.31 DMX modes #define DMX_MODE_DISABLED 0 //not used #define DMX_MODE_SINGLE_RGB 1 //all LEDs same RGB color (3 channels) #define DMX_MODE_SINGLE_DRGB 2 //all LEDs same RGB color and master dimmer (4 channels) #define DMX_MODE_EFFECT 3 //trigger standalone effects of WLED (11 channels) #define DMX_MODE_MULTIPLE_RGB 4 //every LED is addressed with its own RGB (ledCount * 3 channels) #define DMX_MODE_MULTIPLE_DRGB 5 //every LED is addressed with its own RGB and share a master dimmer (ledCount * 3 + 1 channels) #define DMX_MODE_MULTIPLE_RGBW 6 //every LED is addressed with its own RGBW (ledCount * 4 channels) //Light capability byte (unused) 0bRCCCTTTT //bits 0/1/2/3: specifies a type of LED driver. A single "driver" may have different chip models but must have the same protocol/behavior //bits 4/5/6: specifies the class of LED driver - 0b000 (dec. 0-15) unconfigured/reserved // - 0b001 (dec. 16-31) digital (data pin only) // - 0b010 (dec. 32-47) analog (PWM) // - 0b011 (dec. 48-63) digital (data + clock / SPI) // - 0b100 (dec. 64-79) unused/reserved // - 0b101 (dec. 80-95) virtual network busses // - 0b110 (dec. 96-111) unused/reserved // - 0b111 (dec. 112-127) unused/reserved //bit 7 is reserved and set to 0 #define TYPE_NONE 0 //light is not configured #define TYPE_RESERVED 1 //unused. Might indicate a "virtual" light //Digital types (data pin only) (16-31) #define TYPE_WS2812_1CH 20 //white-only chips #define TYPE_WS2812_WWA 21 //amber + warm + cold white #define TYPE_WS2812_RGB 22 #define TYPE_GS8608 23 //same driver as WS2812, but will require signal 2x per second (else displays test pattern) #define TYPE_WS2811_400KHZ 24 //half-speed WS2812 protocol, used by very old WS2811 units #define TYPE_SK6812_RGBW 30 #define TYPE_TM1814 31 //"Analog" types (PWM) (32-47) #define TYPE_ONOFF 40 //binary output (relays etc.) #define TYPE_ANALOG_1CH 41 //single channel PWM. Uses value of brightest RGBW channel #define TYPE_ANALOG_2CH 42 //analog WW + CW #define TYPE_ANALOG_3CH 43 //analog RGB #define TYPE_ANALOG_4CH 44 //analog RGBW #define TYPE_ANALOG_5CH 45 //analog RGB + WW + CW //Digital types (data + clock / SPI) (48-63) #define TYPE_WS2801 50 #define TYPE_APA102 51 #define TYPE_LPD8806 52 #define TYPE_P9813 53 //Network types (master broadcast) (80-95) #define TYPE_NET_DDP_RGB 80 //network DDP RGB bus (master broadcast bus) #define TYPE_NET_E131_RGB 81 //network E131 RGB bus (master broadcast bus) #define TYPE_NET_ARTNET_RGB 82 //network ArtNet RGB bus (master broadcast bus) #define IS_DIGITAL(t) ((t) & 0x10) //digital are 16-31 and 48-63 #define IS_PWM(t) ((t) > 40 && (t) < 46) #define NUM_PWM_PINS(t) ((t) - 40) //for analog PWM 41-45 only #define IS_2PIN(t) ((t) > 47) //Color orders #define COL_ORDER_GRB 0 //GRB(w),defaut #define COL_ORDER_RGB 1 //common for WS2811 #define COL_ORDER_BRG 2 #define COL_ORDER_RBG 3 #define COL_ORDER_BGR 4 #define COL_ORDER_GBR 5 #define COL_ORDER_MAX 5 //Button type #define BTN_TYPE_NONE 0 #define BTN_TYPE_RESERVED 1 #define BTN_TYPE_PUSH 2 #define BTN_TYPE_PUSH_ACT_HIGH 3 #define BTN_TYPE_SWITCH 4 #define BTN_TYPE_PIR_SENSOR 5 #define BTN_TYPE_TOUCH 6 #define BTN_TYPE_ANALOG 7 #define BTN_TYPE_ANALOG_INVERTED 8 //Ethernet board types #define WLED_NUM_ETH_TYPES 8 #define WLED_ETH_NONE 0 #define WLED_ETH_WT32_ETH01 1 #define WLED_ETH_ESP32_POE 2 #define WLED_ETH_WESP32 3 #define WLED_ETH_QUINLED 4 #define WLED_ETH_TWILIGHTLORD 5 #define WLED_ETH_ESP32DEUX 6 //Hue error codes #define HUE_ERROR_INACTIVE 0 #define HUE_ERROR_UNAUTHORIZED 1 #define HUE_ERROR_LIGHTID 3 #define HUE_ERROR_PUSHLINK 101 #define HUE_ERROR_JSON_PARSING 250 #define HUE_ERROR_TIMEOUT 251 #define HUE_ERROR_ACTIVE 255 //Segment option byte bits #define SEG_OPTION_SELECTED 0 #define SEG_OPTION_REVERSED 1 #define SEG_OPTION_ON 2 #define SEG_OPTION_MIRROR 3 //Indicates that the effect will be mirrored within the segment #define SEG_OPTION_NONUNITY 4 //Indicates that the effect does not use FRAMETIME or needs getPixelColor #define SEG_OPTION_FREEZE 5 //Segment contents will not be refreshed #define SEG_OPTION_TRANSITIONAL 7 //Segment differs return byte #define SEG_DIFFERS_BRI 0x01 #define SEG_DIFFERS_OPT 0x02 #define SEG_DIFFERS_COL 0x04 #define SEG_DIFFERS_FX 0x08 #define SEG_DIFFERS_BOUNDS 0x10 #define SEG_DIFFERS_GSO 0x20 #define SEG_DIFFERS_SEL 0x80 //Playlist option byte #define PL_OPTION_SHUFFLE 0x01 // WLED Error modes #define ERR_NONE 0 // All good :) #define ERR_EEP_COMMIT 2 // Could not commit to EEPROM (wrong flash layout?) #define ERR_JSON 9 // JSON parsing failed (input too large?) #define ERR_FS_BEGIN 10 // Could not init filesystem (no partition?) #define ERR_FS_QUOTA 11 // The FS is full or the maximum file size is reached #define ERR_FS_PLOAD 12 // It was attempted to load a preset that does not exist #define ERR_FS_IRLOAD 13 // It was attempted to load an IR JSON cmd, but the "ir.json" file does not exist #define ERR_FS_GENERAL 19 // A general unspecified filesystem error occured #define ERR_OVERTEMP 30 // An attached temperature sensor has measured above threshold temperature (not implemented) #define ERR_OVERCURRENT 31 // An attached current sensor has measured a current above the threshold (not implemented) #define ERR_UNDERVOLT 32 // An attached voltmeter has measured a voltage below the threshold (not implemented) //Timer mode types #define NL_MODE_SET 0 //After nightlight time elapsed, set to target brightness #define NL_MODE_FADE 1 //Fade to target brightness gradually #define NL_MODE_COLORFADE 2 //Fade to target brightness and secondary color gradually #define NL_MODE_SUN 3 //Sunrise/sunset. Target brightness is set immediately, then Sunrise effect is started. Max 60 min. #define NTP_PACKET_SIZE 48 //maximum number of rendered LEDs - this does not have to match max. physical LEDs, e.g. if there are virtual busses #ifndef MAX_LEDS #ifdef ESP8266 #define MAX_LEDS 1664 //can't rely on memory limit to limit this to 1600 LEDs #else #define MAX_LEDS 8192 #endif #endif #ifndef MAX_LED_MEMORY #ifdef ESP8266 #define MAX_LED_MEMORY 4000 #else #define MAX_LED_MEMORY 64000 #endif #endif #ifndef MAX_LEDS_PER_BUS #define MAX_LEDS_PER_BUS 4096 #endif // string temp buffer (now stored in stack locally) #ifdef ESP8266 #define SETTINGS_STACK_BUF_SIZE 2048 #else #define SETTINGS_STACK_BUF_SIZE 3096 #endif #ifdef WLED_USE_ETHERNET #define E131_MAX_UNIVERSE_COUNT 20 #else #ifdef ESP8266 #define E131_MAX_UNIVERSE_COUNT 9 #else #define E131_MAX_UNIVERSE_COUNT 12 #endif #endif #ifndef ABL_MILLIAMPS_DEFAULT #define ABL_MILLIAMPS_DEFAULT 850 // auto lower brightness to stay close to milliampere limit #else #if ABL_MILLIAMPS_DEFAULT < 250 // make sure value is at least 250 #define ABL_MILLIAMPS_DEFAULT 250 #endif #endif // PWM settings #ifndef WLED_PWM_FREQ #ifdef ESP8266 #define WLED_PWM_FREQ 880 //PWM frequency proven as good for LEDs #else #define WLED_PWM_FREQ 19531 #endif #endif #define TOUCH_THRESHOLD 32 // limit to recognize a touch, higher value means more sensitive // Size of buffer for API JSON object (increase for more segments) #ifdef ESP8266 #define JSON_BUFFER_SIZE 10240 #else #define JSON_BUFFER_SIZE 20480 #endif #ifdef WLED_USE_DYNAMIC_JSON #define MIN_HEAP_SIZE JSON_BUFFER_SIZE+512 #else #define MIN_HEAP_SIZE 4096 #endif // Maximum size of node map (list of other WLED instances) #ifdef ESP8266 #define WLED_MAX_NODES 24 #else #define WLED_MAX_NODES 150 #endif //this is merely a default now and can be changed at runtime #ifndef LEDPIN #ifdef ESP8266 #define LEDPIN 2 // GPIO2 (D4) on Wemod D1 mini compatible boards #else #define LEDPIN 2 // Changed from 16 to restore compatibility with ESP32-pico #endif #endif #ifdef WLED_ENABLE_DMX #if (LEDPIN == 2) #undef LEDPIN #define LEDPIN 1 #warning "Pin conflict compiling with DMX and LEDs on pin 2. The default LED pin has been changed to pin 1." #endif #endif #ifndef DEFAULT_LED_COUNT #define DEFAULT_LED_COUNT 30 #endif #define INTERFACE_UPDATE_COOLDOWN 2000 //time in ms to wait between websockets, alexa, and MQTT updates #endif